Unfortunately, nothing seemed to be completely aligned from the factory, so right off the bat, we got cuts that were far from straight. After quite a bit of adjusting and fiddling, we managed to get some pretty decent cuts, though not the cleanest or straightest of the saws we tested. We also weren’t thrilled about how long the blade took to slow down once the saw was powered off. Sometimes you want to turn the saw off, adjust your piece, and make a new cut. When the blade just continues spinning, it starts to reduce your productivity.
Miter gauges are one of those accessories that you may forget about in daily use, but then desperately need if you don’t have one. They’re used with table saws in order to cut angles that aren’t 90 degrees. The best miter gauges include hard stops at 90 degrees and 45 degrees, which are the angles that you’re most often going to be cutting at. The hard stops make it easy to set the miter gauge to those angles and cut away with confidence.
Power: What kind of woodworking will you do, how often will you do it and what kind of materials will you use? If portability is important, you'll want a jobsite saw. If you're a hobbyist and want a saw that can handle most home shop requirements, a contractor saw might be right for you. If you run a professional shop, you might want the power and durability of a cabinet saw.

Electronic feedback circuitry can be useful to increase the lifespan of the engine and make the wood router easier to handle. Essentially it monitors the engine load and adjusts the torque to match. This prevents the router motor from lagging or stalling when hitting dense patches of wood, which also helps reduce the chance of it spinning out of control when it suddenly speeds up again.


For our customers who are passionate about woodworking, we offer an extensive selection of tools and accessories to help your woodworking projects come to life. Whether you are a professional carpenter, construction manager or simply wish to build a DIY project, you will find everything that you need on our Amazon.com Woodworking page. Our selection ranges from, screwdriver sets to air filtration, band saws, sanders, drill presses, dust collectors, jointers, laminate trimmers, lathes, planers, benchtop, plate joiners, belt sanders, router combo kits, shapers, sharpener, barn door hardware, circular saws, router tables, router bits, planer, tool box, wood glue, nail gun, table saws, hammers and more.
Consequently, they’re going to be a bit heavier than benchtop models. However, their expanding frames mean that you’ll be able to use them even in places where you don’t have access to a table or bench. This is great for construction work, or situations where you’re going to be working outside. This type tends to be a little bit bigger than the benchtop variety, and often has more rip capacity as well.
Power: What kind of woodworking will you do, how often will you do it and what kind of materials will you use? If portability is important, you'll want a jobsite saw. If you're a hobbyist and want a saw that can handle most home shop requirements, a contractor saw might be right for you. If you run a professional shop, you might want the power and durability of a cabinet saw.
Woodworking expert Sandor Nagyszalanczy tested the best jigsaws on the market to determine what features worked well in the shop and which was best overall. I’ve always thought of a jigsaw as a sort of “poor man’s band saw.” During my early woodworking days when I lacked both the funds and space for a band saw, I used the best jigsaw I could find (I borrowed money from a friend to buy it). I used that jigsaw for all my curve cutting tasks, as well as the jobs a band saw couldn’t do: pocket cuts, inside circular cutouts, and all manner of trimming inside built-in cabinets and furniture. Nearly 35 years later, when it came time to pick a batch of jigsaws to review for Woodoworker's Journal, I was anxious to try out the “top-shelf” models offered by the best known power tool manufacturers. These include the best offerings from Bosch, DeWALT, Festool, Hitachi, Makita, Metabo and Milwaukee. The Porter-Cable 9543 was slated to be part of this group, but was, unfortunately, recently discontinued. I also tried to include a jigsaw made by the Swiss power tool company Hilti, but they chose not to participate in the article. Instead of discussing each saw individually, I will compare all of their attributes and cutting abilities in two sections: The first contrasts the features and accessories of the seven models. The second section describes the performance tests I put each jigsaw through and reports on how well each model fared.
The JET JDP-17MF Floor Drill Press is a The JET JDP-17MF Floor Drill Press is a true woodworker's drill press. With 16-speeds it lets you choose the best speed for the job. It comes equipped with a quick release crank operated worktable; work light X-pattern mounting grooves depth stop and adjustable tension spindle return spring which is ideal ...  More + Product Details Close

My Stanley 51/2 was in a bit of a state when I got it and refurbing it took a bit of time and cash. Now it works a treat and looks like new. I’m nearly through the bench build and have spend hours using it – it really is a workhorse piece of kit. I did some final cleaning up of some oak legs the other day and I can’t really see how a smaller plain would do a better job.
[caption id="attachment_7419" align="aligncenter" width="405"] The author prefers a longer handled jigsaw, as it allows you to grip it at different angles more easily for different cuts. Handle & trigger: A good handle is important on a jigsaw for user comfort and also because a solid grip is essential to controlling the movement of the tool during cutting. All of the saws in this group, save the Festool, have a rubber-like overmold covering their handles. Overmolds are softer to the touch than hard plastic, provide a more secure grip and even dampen tool vibration slightly. Of the seven saws, the handles on the Makita and Hitachi fit my medium-sized hands the best. I also liked the longer handles found on these saws (as well as several others) because their length allows for a varied grip to suit different working positions. The pommel at the front of the DeWALT’s handle allows a two-handed grip — helpful when cutting in awkward positions. [caption id="attachment_7420" align="aligncenter" width="405"] Wider triggers offer you more gripping options and control, whereas narrower jigsaw triggers can be clumsy and hard to grip while cutting. A jigsaw’s most important operational feature is its trigger that switches the tool on and off. I generally prefer a wider tool trigger that allows twofinger operation, to help reduce hand fatigue. Wide triggers also let users place their hands in a variety of positions along the tool’s handle. The Festool was the only saw in the group with a narrow trigger, and I didn’t like its stiff, clunky on/off action. I preferred the comfortable, smooth-operating, wide triggers on the DeWALT and Makita. All the saws have trigger locks, so you don’t have to hold the trigger on during long cuts. The Bosch’s trigger lock is the only one designed for use by left- or right-hand users. The Bosch, DeWALT and Milwaukee saws feature variable triggers that let you ramp up the speed of the blade gradually, up to the maximum set on its variable-speed dial. This is useful when starting cuts in very hard and/or splintery woods as well as materials prone to chipping, like tile and plastics. The Bosch’s unique trigger works with a two-step action: Pull the trigger lightly, and the saw immediately switches on to a slow speed. Press the trigger a little farther and it fully varies the speed up to the set maximum. Although the Bosch’s trigger works well enough, I prefer the triggers on the DeWALT and Milwaukee, which let you ramp the speed up from zero to the maximum set speed with one continuous pull. [caption id="attachment_7421" align="aligncenter" width="480"] All the portable jigsaws had variable speed control dials, but the locations varied, with some being harder to reach while operating than others. Variable-speed & soft start: All seven saws are variable-speed models with dials that allow you to set the motor speed and, hence, the number of blade strokes per minute. This makes a jigsaw a more versatile cutting machine: Choose slower speeds for fine cuts and when cutting dense materials and plastics and faster speeds for quicker, rougher cuts in lighter woods and porous materials. Interestingly, the saws with the highest maximum speeds didn’t necessarily cut faster than those with slower speeds. I like the position of the speed dials on the Hitachi and Festool saws. These are easier to see and set than the rear-mounted dials on the Bosch, Metabo and Makita. The DeWALT and Milwaukee have trigger-mounted speed dials that I find hard to see and set without tipping or inverting the saw. The Metabo and Makita both feature “soft-start” motor electronics that ramp up motor speed gradually when the tool’s trigger is pulled. Soft start can prevent the saw from suddenly jerking if you start cutting with the blade in contact with the material. But, overall, I found soft start more of an irritation than an aid; I didn’t like having to wait for the saw to come up to speed each time I started a cut. [caption id="attachment_7422" align="aligncenter" width="495"] One of the things to check when selecting a jigsaw is how comfortable the orbital blade adjustment is, as this will ultimately guide how aggressive your cuts can be. Selectable blade orbit: Probably the single most important feature on a topnotch jigsaw is its orbital blade action. This mechanism moves the blade forward slightly during the upstroke cut, resulting in a more aggressive cutting action than if the blade simply reciprocated up and down. The mechanism also moves the saw blade back slightly, so it clears the kerf during the return down stroke and saves wear on the teeth. Adjusting the amount of blade orbit makes the saw cut more or less aggressively. Most saws have four orbit settings: 0 (no orbit) or 1 for cutting metals and plastics; 1 or 2 for fine and curved cuts; and 3 (maximum orbit) for faster, rougher cuts. The Metabo features five orbit selections instead of four, but I didn’t find the greater range of select ability to be particularly necessary or useful. The Milwaukee has a small, somewhat handy blade orbit and speed selection chart mounted on the side of the tool. [caption id="attachment_7423" align="aligncenter" width="465"] While they are historically a bandsaw accessory, blade guides are starting to make their way onto jigsaws like these from Festool and Bosch. Blade guide systems: A unique feature found on the Festool and Bosch saws is a special saw blade guide positioned below the orbit mechanism’s guide wheel. These small metal guides work like the guide blocks on a band saw, to help stabilize the blade and keep it from deflecting during cutting. The Festool’s guide has two small prongs that contact the blade more closely at the back than at the front. They’re user-adjustable via an included Allen wrench. The Bosch’s “Precision Guide Control” has two small parallel blocks that are user-engaged via a small pushbutton. The blocks apply light spring-loaded pressure against the sides of the blade. The guide’s jaws open automatically when the blade release lever is pulled. Both of these innovative systems are very easy to use and significantly improve performance. [caption id="attachment_7424" align="aligncenter" width="475"] All the jigsaws featured had tool-free blade change systems, which allow you to safely and easily change out blades thanks to a spring loaded lever and clamp. Tool-less blade clamps: All seven jigsaws allow tool-less blade changes, employing a lever that opens the blade clamp on the end of the saw’s plunger — the part that moves the blade up and down. Tool-less blade clamps make changing the tang-style saw blades each model uses quick and easy. But each clamp is different, and some are easier to work with than on others. The Festool, Makita and Bosch blade clamps are among my favorites. The Festool’s “Fast Fix” blade change mechanism has a relatively stiff lever, but its clamp accepts blades without fuss and holds them rock solid. The Makita also has a terrific mechanism with a spring-loaded lever that’s easy to pull open and a clamp that accepts blades easily and positively. As good as these clamps are, the Bosch’s “One Touch” blade change system is my favorite. There’s no clunky mechanism or oversized blade clamp on the end of the plunger, just a simple slot. After pulling back the small, easy-to-use release lever, a spring gently ejects the blade. This can save you from burning your fingers trying to pull a hot blade out of the clamp after a prolonged cutting session. The new blade inserts easily into the Bosch’s plunger slot and latches with a positive feel. [caption id="attachment_7425" align="aligncenter" width="475"] Some jigsaws allow you to change the positioning of the footplate without tools, but most require the use of an Allen wrench which takes time, but isn't a deal breaker. Tilting footplate: Adjusting the angle of a jigsaw’s footplate (a.k.a. “shoe”) allows the saw to make bevel cuts, say for the edge of a picture frame or decorative plaque. While all these jigsaws have tilting footplates, only the Bosch, Milwaukee and DeWALT allow tool-less angle changes. Each of these saws has a lever that releases and locks the footplate easily and quickly. The Bosch’s even includes a separate dial for adjusting locking tightness. I like the Milwaukee’s wide lever the best because it operates smoothly and positively. The other four saws employ an Allen wrench, which conveniently stores on board the tool, for angle changes. Yes, using a wrench does take more time, but then again, how often does the average woodworker take bevel cuts with a jigsaw? Angle detents are very useful for locking in commonly used tilt settings. All the saws have a 0-degree detent for square cuts, and most have detents at 45 degrees and other angles as well. After checking the accuracy of the all-important 90-degree detents, I found that only the Festool and Bosch consistently kept their blades at near perfect square to the footplate. The other saws required a bit of fussing with a try square to get their blades dead on 90 degrees. [caption id="attachment_7426" align="aligncenter" width="475"] Fittings for easy chip extraction is handy, but sadly only comes with more expensive jigsaws from Metabo, Bosch and Festool Dust collection and sawdust blower: Having written many articles and several books on woodshop dust control, I’m a huge advocate of built-in dust collection on portable power tools. The three most expensive jigsaws in this group — the Festool, Bosch and Metabo — come with a chip extractor fitting for dust collection; it’s an optional accessory for the other four saws. This plastic fitting clips into the back of the saw’s footplate and connects to a small diameter vacuum hose (the Bosch comes with a hose adapter). A clear plastic chip guard snaps in place over the front of the saw to enclose the blade area and enhance chip collection. The guard must be removed for blade changes. I only tested dust collection with the three saws that came standard with the extractor fitting. Both the Bosch and Festool collected chips effectively, but there was a problem: Their chip guards limited the visibility of the line of cut, and as fine dust built up on the inside of the guard, it became nearly impossible to see. Visibility was considerably better with the Metabo when using dust collection, as its chip guard is much taller and larger and didn’t seem to attract as much fine dust. [caption id="attachment_7427" align="aligncenter" width="455"] Bosch's solution to not having dust collector fittings is a directed blower, which can be controlled via a switch on the side of the tool. An alternative means of clearing sawdust from the line of cut is to simply blow it away. All the saws feature a dust blower that uses air channeled from the motor fan to blow dust away from just in front of the blade. The blowers on all the saws do a pretty good job, save the Makita, whose airflow is rather sluggish. The Bosch has a blower On/Off lever, and the DeWALT and Milwaukee have controls for reducing the amount of blown air. Shutting off or turning down the airflow is desirable when you’re working inside your home and don’t want to launch sawdust everywhere, or when blown dust might end up in your eyes, say when jigsawing plumbing and electrical cutouts inside a kitchen cabinet. [caption id="attachment_7428" align="aligncenter" width="455"]Curiously, only the three least expensive saws tested, like this one from Hitachi, were equipped with an LED guide light. Built-in light: The Hitachi, Makita and Milwaukee all include one of my favorite portable power tool features: a built-in LED light. Interestingly, these are the three lowest-priced saws in the group (I guess toolmakers figure that the folks that buy more expensive saws also have better eyesight!). A built-in light is particularly welcome on a jigsaw, since the overhanging body tends to cast a shadow in the area of the blade. The Hitachi’s light has a small plastic pointer that conducts some of the LED’s light and sticks down in front of the blade. Although its goal is to better visually define the line of cut, I found it actually obscured the work area. [caption id="attachment_7429" align="aligncenter" width="495"] DeWalt jigsaws (amongst others) come with a removable footplate cover that is made of plastic to prevent the metal plate from scraping the wood. Other features: An accessory plastic shoe cover comes with the Bosch, Makita, Milwaukee and DeWALT jigsaws. This thin, slick plastic cover snaps in place over the tool’s footplate, allowing you to saw delicate materials — decorative veneers, plastics, Corian® countertops — without fear of causing scratches. The Festool doesn’t include a shoe cover, but it doesn’t really need one. Its cast alloy footplate already has a slick plastic covering. [caption id="attachment_7430" align="aligncenter" width="445"] Almost all jigsaws currently available come with a small, plastic anti-splitter insert that is very useful when cutting chipping prone materials like plywood. All the jigsaws in the group, except the Hitachi, come with a plastic anti-splinter insert. This small accessory snaps into its footplate to surround the area directly around the blade, like a zero-clearance throat plate in a table saw. These inserts really do help reduce splintering, and I recommend using them when taking fine cuts on splinter-prone woods and plywoods, as well as materials with delicate surfaces, such as melamine. Except for the economy-priced Hitachi, all the jigsaws in the group come with a plastic tool case. The Bosch and Festool saws have special stackable cases, each part of a system that allows multiple cases to be latched together for storage or transport. Like all other current Festool portable power tools, the Trion jigsaw features a detachable “Plug It” power cord. This makes it easier to stow, as you don’t have to wrap the cord around the tool. Plus, you can easily replace a damaged cord by simply plugging in a new one. The back of the Hitachi’s body has a loop molded in, making it easy to connect the tool to a lanyard or other hook — a nice feature if you work on a roof or ladder.
The JET JDP-17MF Floor Drill Press is a The JET JDP-17MF Floor Drill Press is a true woodworker's drill press. With 16-speeds it lets you choose the best speed for the job. It comes equipped with a quick release crank operated worktable; work light X-pattern mounting grooves depth stop and adjustable tension spindle return spring which is ideal ...  More + Product Details Close
This Combination Machine is similar to the G0634Z This Combination Machine is similar to the G0634Z except it sports our popular Polar Bear colors. It also has an end-mounted fence so you can work as close to your shop wall as possible. This feature is a real space saver and since this is a combination machine you're saving ...  More + Product Details Close

Some table saws come with a miter gauge, though the quality tends to be uneven. Some are great, and will serve you well for a long time, while others are flimsy or struggle to hold the correct angle or both. This is something that can most easily be determined by reading online reviews, though it’s always great to get your hands on a demonstration model, if possible.
While it is possible to rip thin stock using only the table saw’s fence, you have to remove the guard and squeeze your stock and push stick through the dangerously narrow gap between the blade and your fence. Can you say “kickback”? Even if you successfully navigate this dangerous cut, you inevitably end up with burn marks and uneven cuts that have to be sanded out.
Whether you are a beginner or a DIY professional, if you have a love for the craft of woodworking The Home Depot has got you covered. We have all the essential tools for woodworking that let you hone your craft. Our huge selection of drill presses and miter saws will put the power in your hands to complete your projects faster and easier. And whether you are looking for the strength of a powerful router or the versatility of a lathe, you can find everything you need to help with projects, large and small. If your carpentry plans also include building materials, you don't need to look any further than The Home Depot. From wood and lumber to decking and fencing materials, it's all right here.
For people who need a multitasking jigsaw and need to cut various materials including wood, plastic, PVC, and steel, we recommend getting this PORTER-CABLE PCE345 6-Amp Orbital Jigsaw which is our 3rd pick for the list. This corded jigsaw for woodworking is quite powerful since it is able to deliver a cutting speed of up to 3,200 which only a corded machine can deliver.
In most situations, you can take the dust bag off of the port and hook up a shop vac or an industrial dust-collection system. Many table saws make use of a standard-size dust port between 2-1/2 and 4 inches in diameter, which means it may be compatible with equipment that you already own. Some models forgo the dust bag altogether, in the expectation that you’ll be using some sort of dust collection system.
Woodworking tools at Highland Woodworking - shop our comprehensive tool selection for the best in woodworking tools. Our lines include woodworking hand tools & power tools, joinery jigs, The World's Safest Tablesaw and The Best Bandsaw Blade Selection. Along with woodworking tools from top tool brands, we stock the woodworking materials & supplies you need everyday. View all tools at Highland Woodworking home to over 10,000 Woodworking Tools or browse through our Woodworking Tools sub-categories below. Be sure to check out our Woodworking Tool Sale page where you will find special offers and tool deals.
In most situations, you can take the dust bag off of the port and hook up a shop vac or an industrial dust-collection system. Many table saws make use of a standard-size dust port between 2-1/2 and 4 inches in diameter, which means it may be compatible with equipment that you already own. Some models forgo the dust bag altogether, in the expectation that you’ll be using some sort of dust collection system.
There is a BIG difference in a cheap jigsaw and one that costs a bit more. Seriously, a BIG difference. I hated using my old jigsaw ($35 dollar hardware store special.) This one is awesome. Glides through plywood. Has several settings that actually make a difference in how it cuts. If you are on the fence about buying a more expensive jigsaw, do it. There really is that big of a difference.

Contractor models also tend to be more powerful and more precise than portable saws, which gives them a definite upside if you’re going to be doing lots of work, or work that requires a fine degree of precision. This type can also be a good choice if you’re going to leave your table saw in one place for extended periods of time, while still being light enough that they can be moved if you need to do so.
These models tend to be much heavier than portable models, clocking in at 200+ pounds in many circumstances, which mean you may need another person in order to move them safely. The big upside to this model is that that additional weight goes to good use. They tend to have much larger rip capacities, and the table top tends to be more durable and stable than the expanding systems used in portable models.
Karen Bennett lives in Chicago with her family, and when she’s not writing, she can usually be found practicing yoga or cheering on her kids at soccer games. She holds a master’s.degree in journalism and a bachelor’s in English, and her writing has been published in various local newspapers, as well as “The Cheat Sheet,” “Illinois Legal Times,” and “USA Today.” She has also written search engine news page headlines and worked as a product manager for a digital marketing company. Her expertise is in literature, nonfiction, textbooks, home products, kids' games and toys, hardware, teaching accessories, and art materials.
Whether you are a beginner or a DIY professional, if you have a love for the craft of woodworking The Home Depot has got you covered. We have all the essential tools for woodworking that let you hone your craft. Our huge selection of drill presses and miter saws will put the power in your hands to complete your projects faster and easier. And whether you are looking for the strength of a powerful router or the versatility of a lathe, you can find everything you need to help with projects, large and small. If your carpentry plans also include building materials, you don't need to look any further than The Home Depot. From wood and lumber to decking and fencing materials, it's all right here.
×